Vehicles
Sections
63 not categorized PORSCHE 997 HIGH TORQUECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 (includes uncategorized and accessory items) SP363F What good is more horsepower if it isn't transferred to the ground? The clutch is the main link between the power your engine produces and the transmission, but all too often it is also the weak link. Many stock clutches simply will not last under harsh driving conditions or continual hard launches. When a car is making more horsepower than stock the factory clutch is under even more strain. This can cause premature clutch wear and costly repair bills. Spec clutch solves this problem with their line of performance clutches. With increased surface area spec clutches give your transmission more 'bite' while increasing reliability and performance. General Fitment911 1994-98
From $1,149.95
Make a selection SP623 What good is more horsepower if it isn't transferred to the ground? The clutch is the main link between the power your engine produces and the transmission, but all too often it is also the weak link. Many stock clutches simply will not last under harsh driving conditions or continual hard launches. When a car is making more horsepower than stock the factory clutch is under even more strain. This can cause premature clutch wear and costly repair bills. Spec clutch solves this problem with their line of performance clutches. With increased surface area spec clutches give your transmission more 'bite' while increasing reliability and performance. General Fitment911 1994-98
From $999.95
Make a selection SP365 Spec stage 5 clutch Porsche 993 3.6l 95-98 General Fitment911 1994-98
From $1,099.95
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 21011199300 Perfect for those who are looking for a small increase in sound and performance, with subtle low tones and more pronounced higher pitched rasp. If you are looking for a more conservative muffler or are running sport cats this muffler is a perfect choice. - + 5 crank hp & + 4 crank torque. - total weight is 28 lbs. (12.8 kg). That is a savings of 12 lbs. - t 304 stainless steel (polished). - made in europe. - simple bolt on, modifications are not necessary. - no dme / ecu programming is necessary. We recommend purchasing replacing your aging muffler straps, sleeves, rings and hardware with one of our pre-packaged muffler installation kits. Use part # FVDmk9930011 for 1995 and earlier cars. Use part # FVDmk993001...(choose a part on the right to read more) General Fitment911 1994-98
From $1,148.72
Make a selection 21011199301 More loud, pronounced and aggressive than our TUV version. This muffler is extremely civilized while cruising but unleashes lower deeper tones and a higher pitched rasp in the higher rpms under full load. This is the perfect choice if you are only planning to change your muffler. If you have sport cats this muffler will be considerably louder under full load but should still be civilized enough for cruising. - + 5 crank hp & + 4 crank torque. - total weight is 25 lbs. (11.24 kg). That is a savings of 15 lbs. - t 304 stainless steel (polished). - made in europe. - simple bolt on, modifications are not necessary. - no dme / ecu programming is necessary. We recommend purchasing replacing your aging muffler straps,...(choose a part on the right to read more) General Fitment911 1994-98
From $1,316.32
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 220110997061 More air = more power! The incredible 997.2 Porsche turbo received a completely redesigned engine with many substantial upgrades. This latest turbo is the most powerful, revolutionary and capable Porsche turbo to ever come out of stuttgart. The 997.2 Porsche turbo may have been labeled a facelift but the engine is another major evolutionary leap forward in Porsche's coveted turbo history. This 7th generation turbo engine, titled the 9a1, delivers 500 hp (530 hp in s models) and once again, raises the performance bar in the sports car world. The new 997.2 ipd turbo plenum was considerably more difficult to design and develop than previous plenums. The good news is that all these efforts have yielded a much easi...(choose a part on the right to read more)
$1,094.50
Make a selection 47028608 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$122.10
Make a selection 47075004 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc started producing their filters in 1973 and is one of the most recognized brands in the European automotive industry and is a member of the vdat German tuning association. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. Bmc filtration systems yield more engine performance, both in terms of power and torque without compromising reliability. A bmc sport ...(choose a part on the right to read more)
$225.50
Make a selection 47079801 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$214.50
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,749.95
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,014.10
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,142.80
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection BES98111200SHD For 2012+ 981 facts: - equal length headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - t316 lightweight stainless. - primary diameter 45mm outer , 42mm inner - each header weighs 13 lbs. (6 kg) - reduces thermal stress on the motor. - made in Germany please add 2 engine to header gaskets when ordering - 2 qty 99711110731 power: - 981 (2.7l) = + 12 crank hp (9 kw) & + 11 crank torque (15 nm) - 981s (3.4l) = + 16 crank hp (12kw) & 15 crank torque ( 20 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability ma...(choose a part on the right to read more)
$4,988.50
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$7,420.60
Make a selection BES99101260S - + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)
$5,286.60
Make a selection BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,383.50
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection BES99115000SKR + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 18 lb. (8.5 kg)weight savings over OEM center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - replaces OEM center muffler and connects to OEM header and OEM side mufflers and OEM tips. Please note: this muffler is a direct replacement the 991 Carrera s (3.8l - us model) which comes standard with valves. It is also a direct replacement for the Porsche sport exhaust option. This center muffler bypass for the 991 is one of the most technically advanced for Porsche t...(choose a part on the right to read more)
$3,713.60
Make a selection 47090704 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$368.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |